AirTAC GF600-20 Filter (GF60020M)
The AirTAC AirTAC GF600-20 Filter (GF60020M) is a genuine G-series air filter. It separates condensed water and filters particulate from the compressed-air line through a 40 µm element, with PT3/4" ports and a manual drain. A filter does not set downstream pressure — pair it with a GR regulator, or use a GFR filter regulator, when pressure control is needed.
- TypeAir filter
- Port sizePT3/4"
- Filtering grade40 µm
- DrainManual drain
- Inlet pressure0 - 0.9 MPa (0 - 131 psi)
- Bowl materialAluminium alloy
- ThreadPT
- BracketMounting bracket included
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC GF600-20 Filter (GF60020M)
The GF60020M is an AirTAC G-series air filter that removes water and particulate from compressed air. It provides filtration only - there is no pressure regulation and no lubrication in this unit. This configuration is the size 600 body with 3/4 inch PT ports, the standard 40 um filter element, a manual drain that an operator opens to eject collected condensate, and the mounting bracket included. The bowl on this size 600 unit is aluminium alloy. Because this is the manual-drain version of the GF filter, the maximum inlet pressure is 0 to 0.9 MPa, and the operating temperature range is -5 to 70 C (non-freezing).
This is a genuine AirTAC part sold by an authorised distributor. The G-series filter family spans sizes 200, 300, 400 and 600 with a choice of ports, drain types (differential-pressure, automatic or manual), 40 um or 5 um elements, and PT, G or NPT threads. Flow is published as curves rather than a single rated figure, so we confirm flow and datasheet figures on request before you order.
AirTAC GF600-20 Filter (GF60020M) Technical Specifications
| Model | AirTAC GF600-20 Filter (GF60020M) |
|---|---|
| Series | GF600 air filter |
| Port size | PT3/4" (PT thread) |
| Filtering grade | 40 µm |
| Drain type | Manual drain |
| Bracket | Mounting bracket included |
| Fluid | Compressed air |
|---|---|
| Inlet pressure | 0 - 0.9 MPa (0 - 131 psi) |
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Bowl material | Aluminium alloy |
| Feature | Low pressure loss |
Specifications follow the official AirTAC G-series air-preparation data. The inlet-pressure band is set by the drain type: automatic and differential-pressure drains run 0.15 - 1.0 MPa, a manual drain runs 0 - 0.9 MPa. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: AirTAC GF600-20 Filter (GF60020M)
| GF600 | G-series air filter, 600 body — sets the port range. |
|---|---|
| 20 | Port size PT3/4". This body offers 20 = PT3/4", 25 = PT1". |
| M | Drain: Manual drain. Options are differential (blank), automatic (A) or manual (M). |
| (blank) | Mounting bracket included. A bracket ships by default; J orders it without. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
Field order is size, port, drain, bracket, grade, thread — a blank position takes the default. Example: GF300-10AJW is a 300 body, PT3/8", automatic drain, no bracket, 5 µm element, PT thread.
Size Class
- GF200PT1/8" - PT1/4"
- GF300PT1/4" - PT1/2"
- GF400PT3/8" - PT1/2"
- GF600PT3/4" - PT1"
A larger body carries a larger port and passes more air at the same pressure drop. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure. The GF600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GF600 · PT3/4" · 40 µm |
|---|---|
| One size down | GF400 |
| Line order | Filter first, then regulator, then lubricator |
Where the AirTAC GF600-20 Filter (GF60020M) Is Used
Truck maintenance bay air supply
Installed on the shop-air drop serving vehicle-lift and impact-wrench stations in a truck or bus maintenance bay, the filter removes water and dirt from the plant supply, with the manual drain emptied during end-of-shift checks.
Conveyor system air take-off
Mounted on the 3/4 inch air line feeding conveyor drive and gate cylinders in a distribution warehouse, the size 600 body supplies the high draw of the line while the manual drain is cleared during scheduled maintenance.
Assembly cell air preparation
Fitted ahead of nutrunners, clamps and air tools at an assembly cell, the standard 40 um element protects the tools from water and particulate, with the included bracket fixing the filter to the cell frame.
Is the AirTAC GF600-20 Filter (GF60020M) the Right Filter?
Size 600 with 3/4 inch PT ports is the largest step in the G-series filter range, so select it when your line demands high air volume - but size against the required flow, not just the pipe. The M code gives a manual drain: the operator opens the drain to discharge condensate, which suits installations with scheduled maintenance rounds or where a dry-air supply means little water collects. Note that with the manual drain the maximum inlet pressure is 0.9 MPa rather than 1.0 MPa. The standard 40 um element covers general plant-air protection; the 5 um (W) variant exists for finer duty. Thread is PT as standard, with G (BSPP) and NPT as catalogue options, and the mounting bracket is included. Flow is published as curves, not a single rating, so ask us to confirm sizing against your application before ordering.
Quick checklist
- ✓ Body size for your peak flow (PT3/4" here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain: differential, automatic or manual
- ✓ Manual drain caps inlet at 0.9 MPa
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Bracket needed, or order with J
Installation & Maintenance Notes
- check Mount vertically, bowl down, and follow the airflow arrow.
- check Put the filter first in the air-preparation line.
- check Keep inlet pressure within 0 - 0.9 MPa (0 - 131 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Replace the 40 µm element when pressure loss rises.
The aluminium-alloy bowl on the GF600 suits harsher environments than a PC bowl. A filter removes water and particulate only; it does not regulate pressure or add lubrication.
AirTAC GF600-20 Filter (GF60020M) FAQ
AirTAC publishes filter flow as performance curves rather than a single rated figure, so we do not quote one number. Send us your application details and we will confirm the flow and the full datasheet for the GF60020M on request before you order.
The M code replaces the default differential-pressure drain with a drain the operator opens to discharge condensate. On this GF filter the manual-drain version also has a maximum inlet pressure of 0 to 0.9 MPa instead of 1.0 MPa. An automatic drain variant is available if you want hands-free condensate removal.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for AirTAC GF600-20 Filter (GF60020M)
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7-8 hours.