AirTAC GF600-25 Filter (GF60025AJW)
The AirTAC AirTAC GF600-25 Filter (GF60025AJW) is a genuine G-series air filter. It separates condensed water and filters particulate from the compressed-air line through a 5 µm element, with PT1" ports and a automatic drain. A filter does not set downstream pressure — pair it with a GR regulator, or use a GFR filter regulator, when pressure control is needed.
- TypeAir filter
- Port sizePT1"
- Filtering grade5 µm
- DrainAutomatic drain
- Inlet pressure0.15 - 1.0 MPa (22 - 145 psi)
- Bowl materialAluminium alloy
- ThreadPT
- BracketSupplied without bracket
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC GF600-25 Filter (GF60025AJW)
GF60025AJW is a genuine AirTAC G-series air filter in the size 600 frame, with a 1 inch PT thread as the standard connection. It is a filtration-only unit: it removes water and particulate from compressed air, with no pressure regulation and no lubrication. The W suffix fits the fine 5 um element in place of the standard 40 um grade, the A suffix fits the automatic drain instead of the default differential-pressure drain, and the J suffix means no mounting bracket is supplied. The 600-size bowl is aluminium alloy, maximum inlet pressure is 1.0 MPa (145 psi), and the working temperature range is -5 to 70 C, non-freezing.
The same size 600 frame can be ordered with the standard 40 um element, manual (M) or default differential-pressure drainage, the mounting bracket included, or a G (BSPP) or NPT thread instead of PT. AirTAC publishes filter flow as curves rather than a single rated figure, so we confirm flow and full datasheet details on request.
AirTAC GF600-25 Filter (GF60025AJW) Technical Specifications
| Model | AirTAC GF600-25 Filter (GF60025AJW) |
|---|---|
| Series | GF600 air filter |
| Port size | PT1" (PT thread) |
| Filtering grade | 5 µm |
| Drain type | Automatic drain |
| Bracket | Supplied without bracket |
| Fluid | Compressed air |
|---|---|
| Inlet pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Bowl material | Aluminium alloy |
| Feature | Low pressure loss |
Specifications follow the official AirTAC G-series air-preparation data. The inlet-pressure band is set by the drain type: automatic and differential-pressure drains run 0.15 - 1.0 MPa, a manual drain runs 0 - 0.9 MPa. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: AirTAC GF600-25 Filter (GF60025AJW)
| GF600 | G-series air filter, 600 body — sets the port range. |
|---|---|
| 25 | Port size PT1". This body offers 20 = PT3/4", 25 = PT1". |
| A | Drain: Automatic drain. Options are differential (blank), automatic (A) or manual (M). |
| J | Supplied without bracket. A bracket ships by default; J orders it without. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
Field order is size, port, drain, bracket, grade, thread — a blank position takes the default. Example: GF300-10AJW is a 300 body, PT3/8", automatic drain, no bracket, 5 µm element, PT thread.
Size Class
- GF200PT1/8" - PT1/4"
- GF300PT1/4" - PT1/2"
- GF400PT3/8" - PT1/2"
- GF600PT3/4" - PT1"
A larger body carries a larger port and passes more air at the same pressure drop. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure. The GF600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GF600 · PT1" · 5 µm |
|---|---|
| One size down | GF400 |
| Line order | Filter first, then regulator, then lubricator |
Where the AirTAC GF600-25 Filter (GF60025AJW) Is Used
Instrument air on test rigs
Fine pre-filtration of the air feeding gauges, transducers and instrumentation on a plant test bench, mounted on the rig's own backplate.
High-speed sorting line air
Filtering the supply air to ejector valves and blowing stations on a high-speed sorting and conveying line served from a 1 inch header.
Coating line air drop
Particulate removal on the air drop feeding spray equipment in a coating or finishing cell, as part of a staged filtration setup.
Is the AirTAC GF600-25 Filter (GF60025AJW) the Right Filter?
Choose this configuration when your size 600, 1 inch PT line needs finer particulate removal: the W option's 5 um element instead of the standard 40 um grade. It carries the automatic drain (A) and no bracket (J), so it suits manifold or own-plate mounting; drop the J suffix for the factory bracket. G (BSPP) and NPT are thread alternatives to PT if your piping standard differs.
Flow is published as curves, not a single rating, so ask us to confirm sizing against your application before you order.
Quick checklist
- ✓ Body size for your peak flow (PT1" here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain: differential, automatic or manual
- ✓ Manual drain caps inlet at 0.9 MPa
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Bracket needed, or order with J
Installation & Maintenance Notes
- check Mount vertically, bowl down, and follow the airflow arrow.
- check Put the filter first in the air-preparation line.
- check Keep inlet pressure within 0.15 - 1.0 MPa (22 - 145 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Replace the 5 µm element when pressure loss rises.
The aluminium-alloy bowl on the GF600 suits harsher environments than a PC bowl. A filter removes water and particulate only; it does not regulate pressure or add lubrication.
AirTAC GF600-25 Filter (GF60025AJW) FAQ
AirTAC publishes filter flow as performance curves rather than a single rated figure, so we do not state a rated flow for this unit. Send us your line size and air demand and we will confirm the flow figures from the datasheet on request before you order.
The 40 um element is the standard grade for general plant air; the W suffix on this model specifies the finer 5 um grade for applications that call for finer particulate removal. Both are catalogue options on the same size 600 frame, which also offers manual (M) or default differential-pressure drainage and a bracket when you omit the J suffix.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for AirTAC GF600-25 Filter (GF60025AJW)
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7-8 hours.