Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10
The AirTAC JSIJ100~125 Adjustable Cylinder JSIJ100X200-10 is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø100mm bore and 200mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke200 mm
- Port sizeG1/2
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10
The hard-anodized aluminum barrel integrates cleanly without external tie rods. A G1/2 port feeds the double-acting double rod, and the adjustable air cushions provide 33 mm of end-of-stroke deceleration.
The -10 code means an external adjuster lets you shorten the extend stroke by up to 10 mm right on the floor, giving a usable 190 to 200 mm range while the retract end stays fixed. You can fine-tune the end position without swapping the cylinder. Note that this SKU lacks a magnet, so it cannot take CMSE or DMSE sensors.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10 Technical Specifications
| Model | Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | 4935 N |
| Max (@1.0 MPa) | 719 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10 Is Used
Press Fit Tuning
Dial in the exact 190 to 200 mm extend position on-site to seat bearings without over-traveling.
Pallet Stop Gate
Adjust the stop gate position by 10 mm to accommodate slightly varying pallet depths on the fly.
Is the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10 the Right Cylinder?
The 10 mm adjustable window is ideal for sharing a spare across minor stroke variants or finalizing end-position tuning on-site. Mounting options include FA, LB, TC, TCM1, and TCM2 brackets. For any stroke at or over 300 mm, guide the load externally to prevent side-load wear on the rod seal.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10 FAQ
At 0.5 MPa it pushes 3927 N and pulls 3574 N. At 0.7 MPa it pushes 5497 N and pulls 5003 N. The theoretical maximum force is 801 kgf at 1.0 MPa. It uses a G1/2 air port.
The external adjuster lets you shorten the extend stroke by up to 10 mm on-site, giving a usable range of 190 to 200 mm. The nominal 200 mm stroke is the maximum, and the retract end is fixed. This sets the end position but does not lock the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X200-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.