Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S
The AirTAC JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø100mm bore and 225mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke225 mm
- Port sizeG1/2
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S
The extruded hard-anodized aluminum profile barrel leaves out external rods, making the unit noticeably shorter than a same-bore ISO 15552 cylinder. Air enters through a G1/2 port, driving a 32 mm piston rod with an M26x1.5 thread.
The external stop screw lets you trim the extend stroke by up to 40 mm on site, dropping the usable travel from the 225 mm maximum down to 185 mm without swapping the cylinder. Because the -S suffix adds a piston magnet, you can fit CMSE or DMSE reed and electronic switches directly into the side grooves.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S Technical Specifications
| Model | Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | 4935 N |
| Max (@1.0 MPa) | 719 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×225 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S Is Used
Press Fit Tuning
Dial in the exact 185 to 225 mm extend reach for seating bearings, letting the external stop absorb final position variance without remounting the actuator.
Is the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S the Right Cylinder?
The adjustable-stroke window shines when you need to fine-tune an end position after a fixture change, or when you want one shared spare across several stroke variants. Mounting options cover Basic, FA, LB, TC, TCM1, and TCM2. The built-in magnet supports CMSE/DMSE sensors. For any stroke at or over 300 mm, always guide the load to prevent side-load damage.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S FAQ
At 0.5 MPa it pushes 3927 N and pulls 3574 N. At 0.7 MPa it pushes 5497 N and pulls 5003 N. The theoretical max is 801 kgf at 1.0 MPa. It uses a G1/2 port, a 32 mm rod with an M26x1.5 thread, and has 33 mm adjustable air cushions at both ends.
The nominal 225 mm stroke is the maximum. An external stop screw lets you shorten the extend stroke by up to 40 mm on site, giving a usable range of 185 to 225 mm. The retract end stays fixed. Note that a plain cylinder drifts on air loss, so use an external rod lock or pilot-operated check valve to hold a load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X225-40S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.