Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S
The AirTAC JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø100mm bore and 450mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke450 mm
- Port sizeG1/2
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S
The nominal 450 mm travel is the maximum, yielding a usable 350-450 mm window, while the retract end remains fixed. This on-site tuning lets you dial in the exact end position without swapping the cylinder.
Built with an extruded hard-anodized aluminum profile barrel, the body is shorter and more compact than a same-bore ISO 15552 cylinder. Air connects via a G1/2 port, and adjustable 33 mm cushions decelerate the load at both ends. The -S suffix means a built-in piston magnet is present, allowing CMSE or DMSE sensors to drop directly into the side grooves for position detection.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S Technical Specifications
| Model | Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 450 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | 4935 N |
| Max (@1.0 MPa) | 719 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S Is Used
Pallet Stopper Tuning
Trim the 450 mm extend stroke down to 380 mm on-site to act as an adjustable pallet stop without machining new hard stops.
Press End-Position Set
Dial in the exact lower dead point of a light pressing operation using the 100 mm adjuster window, hitting the precise height every cycle.
Shared Spare Inventory
Keep one actuator in maintenance stock and adjust its extend travel anywhere from 350 to 450 mm to replace several fixed-length units.
Is the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S the Right Cylinder?
The JSIJ adjustable-stroke mechanism is ideal when you need to fine-tune the extend endpoint after installation or want a single spare part that covers several stroke variants. Mounting options include FA, LB, TC, TCM1, and TCM2. Because the stroke is 450 mm, always use an external guide rail to prevent rod bending and absorb side loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S FAQ
At 0.5 MPa it pushes 3927 N and pulls 3574 N. At 0.7 MPa it pushes 5497 N and pulls 5003 N. The theoretical maximum at 1.0 MPa is 801 kgf.
The 450 mm nominal stroke is the maximum. The external adjuster lets you shorten the extend stroke by up to 100 mm on site, giving a usable range of 350-450 mm. The retract end is fixed, and the adjuster sets the end position rather than holding the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X450-100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.