Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S
The AirTAC JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø100mm bore and 5mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke5 mm
- Port sizeG1/2
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S
The hard-anodized aluminum profile barrel keeps the build light, and the G1/2 port feeds the 32 mm rod to handle heavy pressing or clamping duties. A built-in magnet comes standard on this -S SKU, ready to accept CMSE or DMSE sensors in the side grooves for precise position detection.
The -10 code means an external adjuster can shorten the 5 mm extend stroke on site by up to 10 mm, letting you fine-tune the end position without swapping the cylinder. Note that the air cushion only decelerates the piston near the end of travel; use an external rod lock or pilot-operated check valve if you need to hold a load securely on air loss.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S Technical Specifications
| Model | Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 5 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | 4935 N |
| Max (@1.0 MPa) | 719 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×5 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S Is Used
Short-Stroke Pressing
Apply 3927 N of clamping force and dial in the exact 0-5 mm contact position with the external adjuster to avoid over-travel.
End-Stop Calibration
Fine-tune the extend endpoint on-site by up to 10 mm to compensate for mechanical wear without replacing the actuator.
Heavy Pallet Snubbing
Use the compact JIS profile and 200 kg vertical lift capacity to halt heavy pallets precisely in tight conveyor spaces.
Is the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S the Right Cylinder?
Choose the JSIJ when you need on-site end-position tuning across shared spare variants, and pick from Basic, FA, LB, TC, TCM1, or TCM2 mounts. The -S suffix equips the cylinder for CMSE/DMSE switches. Even at a 5 mm stroke, always guide the rod to prevent side-load damage.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S FAQ
At 0.5 MPa it pushes 3927 N and pulls 3574 N. At 0.7 MPa it pushes 5497 N and pulls 5003 N. The theoretical maximum force is 801 kgf at 1.0 MPa. It uses a G1/2 port and a 32 mm rod.
The nominal extend stroke is 5 mm maximum. The -10 code means an external stop screw lets you shorten that extend stroke on site by up to 10 mm, giving a usable extend range of 0-5 mm. The retract end remains fixed, and this mechanism sets the end position rather than locking the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X5-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.