Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30
The AirTAC JSIJ100~125 Adjustable Cylinder JSIJ100X600-30 is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø100mm bore and 600mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke600 mm
- Port sizeG1/2
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30
The hard-anodized aluminum extrusion omits tie rods entirely for a clean, compact exterior. Air connects via a G1/2 port.
The JSIJ100X600-30 uses an external stop screw to shorten the extend stroke on site by up to 30 mm. Your usable extend travel runs 570 to 600 mm, with 600 mm being the maximum. You can fine-tune the end position without swapping the cylinder, while the retract end stays fixed. This SKU lacks a magnet and cannot take a CMSE or DMSE sensor; choose an -S variant if you need position detection.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30 Technical Specifications
| Model | Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 600 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | 4935 N |
| Max (@1.0 MPa) | 719 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30 Is Used
Press Stroke Tuning
Dial in the exact 570 to 600 mm extend end position on a pressing fixture without machining new spacers or changing the cylinder.
Shared Spare Inventory
Keep one cylinder as a backup for multiple 600 mm machines, shortening the extend stroke on site to match specific fixture requirements.
Is the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30 the Right Cylinder?
The adjustable 570 to 600 mm extend window is ideal for sharing a spare across stroke variants or dialing in end positions on site. Mounting options include FA, LB, TC, TCM1, and TCM2 brackets. Because this is a 600 mm stroke, you must support the load with external guides to prevent rod bending and side-load damage. Remember that a plain cylinder drifts on air loss; the cushions only decelerate, so add an external rod lock or pilot-operated check valve for held loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30 FAQ
At 0.5 MPa it pushes 3927 N and pulls 3574 N. At 0.7 MPa it pushes 5497 N and pulls 5003 N. The theoretical maximum force is 801 kgf at 1.0 MPa. It uses a G1/2 port and a 33 mm adjustable air cushion at each end.
An external stop screw lets you shorten the extend stroke by up to 30 mm on site. The usable extend travel is 570 to 600 mm, with 600 mm as the maximum. The retract end is fixed. This mechanism sets the end position and does not lock the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X600-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.