Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10
The AirTAC JSIJ100~125 Adjustable Cylinder JSIJ100X75-10 is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø100mm bore and 75mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ100 mm
- Stroke75 mm
- Port sizeG1/2
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM26×1.5
- CushionAdjustable, 33 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10
The dash-10 code defines an external adjuster that lets you shorten the extend stroke by up to 10 mm on site, dropping the usable forward travel from the 75 mm maximum down to 65 mm so you can fine-tune the end position without remounting the actuator. This plain SKU lacks a magnet and cannot take a CMSE or DMSE sensor, so order an -S variant if you need position detection. Note that the adjustable stop only sets the endpoint; it does not hold the load on air loss, so fit an external rod lock or pilot-operated check valve for vertical safety.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10 Technical Specifications
| Model | Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G1/2 |
| Rod thread | M26×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3525 N | 3525 N |
| 0.7 MPa | 4935 N | 4935 N |
| Max (@1.0 MPa) | 719 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 100 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10 Is Used
Press Fit Tuning
Dial in the exact seating depth of a bearing press by trimming the extend stroke up to 10 mm on site, ensuring perfect insertion without remounting the cylinder.
Pallet Stopper
Fine-tune the stopping position of inbound pallets on a roller conveyor by setting the 75 mm extend stroke to the exact required protrusion.
Is the Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10 the Right Cylinder?
When sizing this 100 mm bore, stepping down to an 80 mm unit drops the 0.5 MPa push force to 2513 N, while moving up to a 125 mm bore raises it to 6136 N, giving you clear boundaries for your 3927 N baseline. The 10 mm extend-shortening window shines when you need on-site end-position tuning or want a single shared spare across slightly different stroke variants. You can mount it via FA, LB, TC, TCM1, or TCM2 brackets. Because this is a non-magnet SKU, you cannot add position sensors; specify the -S version if your control system requires CMSE or DMSE switches. For any stroke length at or above 300 mm, always guide the load to prevent side-load damage to the front cover.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10 FAQ
At 0.5 MPa it pushes 3927 N and pulls 3574 N. At 0.7 MPa it pushes 5497 N and pulls 5003 N. The theoretical maximum force is 801 kgf at 1.0 MPa. This 100 mm bore unit uses a G1/2 port, a 32 mm rod, M26x1.5 rod thread, and 33 mm adjustable air cushions at both ends.
The nominal extend stroke is 75 mm, which is the maximum travel. The external adjuster lets you shorten that forward stroke by up to 10 mm on site, giving a usable extend range of 65 to 75 mm so you can set the exact end position without changing the cylinder. The retract end remains fixed.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ100~125 Adjustable Cylinder JSIJ100X75-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.