Airtac SAID32 Double Rod Cylinder SAID32X35S
The AirTAC SAID32 Double Rod Cylinder SAID32X35S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 35mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ32 mm
- Stroke35 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM10×1.25
- CushionAdjustable, 27 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAID32 Double Rod Cylinder SAID32X35S
The AirTAC SAID32X35-S is a double-acting, double-rod ISO 15552 profile cylinder with a 32mm bore and 35mm stroke. Because a rod exits both end covers, the annulus area is identical on extend and retract, yielding equal push and pull forces of 345N at 0.5 MPa (483N at 0.7 MPa). The -S suffix indicates a built-in magnet for position sensing via CMSE reed or DMSE solid-state switches.
Featuring a 12mm carbon steel rod and M10x1.25 threading, this cylinder provides stable dual-side guidance to resist load rotation. The extruded aluminum barrel includes sensor grooves on both sides, while adjustable air cushions at both ends decelerate the piston over a 27mm cushion length to minimize end-of-stroke impact.
Airtac SAID32 Double Rod Cylinder SAID32X35S Technical Specifications
| Model | Airtac SAID32 Double Rod Cylinder SAID32X35S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAID32 Double Rod Cylinder SAID32X35S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAID32 Double Rod Cylinder SAID32X35S Is Used
Symmetric Force Transfer
Drives a workpiece back and forth with identical 345N thrust and speed in both directions, ensuring perfectly balanced motion for precision transfer arms.
Anti-Rotation Slides
The twin 12mm rods exiting both covers guide the load against torsional twist, keeping inline sliding mechanisms perfectly aligned without external guides.
Through-Rod Sensing
Mounts a position flag or cam on the rear rod end to trigger DMSE solid-state sensors, providing precise end-of-stroke confirmation from the opposite side of the actuator.
Is the Airtac SAID32 Double Rod Cylinder SAID32X35S the Right Cylinder?
Select this 32mm bore model when your mechanism requires symmetric force and speed in both travel directions, or when you need to mount a secondary cam, flag, or tool on the rear rod. If your application needs higher thrust, stepping up to the 40mm bore yields 528N at 0.5 MPa. Conversely, if space is tight and force requirements drop, you would step down to a smaller unit.
This double-rod design is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 double-rod cylinders. It uses the reduced SAID mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR mounts found on single-rod variants. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load. If the application must maintain position without live air pressure, use an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAID32 Double Rod Cylinder SAID32X35S FAQ
Because the double-rod design subtracts the rod area on both sides, the push and pull forces are equal. It generates 345N at 0.5 MPa, 483N at 0.7 MPa, and 621N at 0.9 MPa in both directions.
It is dimensionally interchangeable with ISO 15552 double-rod cylinders, but uses a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR mounts. The included -S magnet works with AirTAC CMSE reed and DMSE electronic sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SAID32 Double Rod Cylinder SAID32X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.