
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X110-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 110mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
It features a 25mm carbon steel piston rod and PT tapered G1/2 ports. By integrating an external adjusting screw, this model provides a usable travel window of 100 to 110mm, allowing you to trim the nominal 110mm stroke by up to 10mm during machine setup.
This fine-tuning capability eliminates the need to swap out the entire cylinder or bolt on external stopper blocks when dialing in final end positions. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch placement, and the standard carbon steel rod handles demanding industrial loads. The rear adjuster functions strictly as a travel stop, meaning the cylinder cannot hold a load without continuous live air pressure.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X110-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 110 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 100 to 110mm retraction point during machine commissioning without machining new hard stops.
Quickly adjust the travel window by up to 10mm to accommodate slight variations in incoming part sizes on the line.
The adjustable stroke is particularly valuable for product changeovers or commissioning phases where the exact end-of-travel position needs micro-adjustments without replacing a fixed-stroke SAI cylinder. When matching ISO 15552 replacements, verify the 110mm stroke, 10mm adjustment range, G1/2 PT ports, and your required mounting style from the SAIJ subset (Basic, FA, LB, TC, FTC, TCM1, TCM2).
Because this model lacks a magnet for position sensing, you cannot use AirTAC CMSE reed or DMSE electronic switches unless you specify an -S variant. For load-holding requirements without live air pressure, note that the rear stopper and air cushions do not act as a lock; consider an SAIL or BSAI cylinder instead. Since the 110mm stroke is relatively short, side-load stress on the 25mm rod is minimal, but external guides remain recommended for heavy off-center loads.
Quick checklist
The rear adjusting screw acts as a mechanical stop, allowing you to shorten the effective travel from the 110mm nominal stroke down to 100mm. This creates a 100-110mm usable window for fine-tuning without changing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.