
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X115-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 115mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
It features a standard 25mm carbon steel piston rod and PT tapered G1/2 ports. By integrating an external stopper at the rear, this actuator allows you to fine-tune the retract position during commissioning without swapping out the entire cylinder.
With a 115mm nominal stroke and a 30mm adjustment code, this model provides an exact usable travel window of 85-115mm. The extruded aluminum barrel includes sensor grooves on both sides, enabling the direct mounting of CMSE reed or DMSE electronic switches if a magnet is specified later. The rear screw acts purely as a travel stop to set the end position, so it does not hold the load without live air pressure.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X115-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 115 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×115 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 85-115mm travel window during format changes to accommodate different package sizes without physically swapping actuators.
Fine-tune the retract stop during machine commissioning to achieve exact alignment without machining custom external spacers.
Set precise retraction limits on automated assembly lines where multiple end-of-stroke positions are required from a single cylinder.
The adjustable 85-115mm window is ideal for product-size changeovers on a line, removing the need to bolt on external stops or buy a fixed-stroke SAI cylinder for every setup. Because the rear adjuster only trims travel and is not a locking device, applications requiring true load-holding without pneumatic pressure must utilize a SAIL pneumatic lock, a BSAI clamp-lock, or an external rod lock.
For an exact ISO 15552 replacement, match the 100mm bore, 115mm stroke, 30mm adjustment, PT G1/2 port, and the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Note that FB, CA, CB, and CR mounts are omitted from this adjustable series. Since the stroke is under 300mm, side-load stress on the 25mm rod is minimal, though external guidance is still recommended for heavy lateral loads.
Quick checklist
If pressure is increased to 0.7MPa, the push force rises to 5497N.
The rear adjuster screw acts as a mechanical stop that trims the nominal 115mm stroke, creating an adjustable travel window of 85-115mm. The adjuster sets the end position but does not lock the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.