
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X115-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 115mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ100X115-75 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a nominal 115 mm stroke that can be dialed back by up to 75 mm, yielding a highly flexible 40 to 115 mm usable travel window for precise end-position tuning.
This adjustable-stroke design eliminates the need to swap cylinders or bolt on external stops during product changeovers. The rear screw acts purely as a travel stop and works in tandem with the standard 36 mm air cushions at both ends to decelerate the payload. For position monitoring, the extruded aluminum barrel includes sensor grooves on both sides, ready to accept AirTAC CMSE reed or DMSE electronic switches if a magnet is specified later.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X115-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 115 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×115 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact end-position from 40 to 115 mm during format size changes on a packaging line without physically replacing the cylinder.
Fine-tune the retraction point during initial commissioning to perfect a pressing or forming operation, avoiding the cost of custom external stoppers.
Provide a flexible travel limit for automated assembly stations where multiple part heights are processed on the same fixture base.
If your setup only needs standard fixed travel without commissioning adjustments, the standard SAI cylinder is a simpler alternative. Because the 115 mm stroke is relatively short, side-load risks are minimal, but always guide the load externally for lateral stability.
When specifying a replacement, ensure you match the 100 mm bore, 115 mm nominal stroke, 75 mm adjustment range, G1/2 PT port, and the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Remember that the rear adjuster is a stop, not a lock; the SAIJ100X115-75 cannot hold a load without live air pressure. For dead-pilot load holding, consider the SAIL or BSAI series instead.
Quick checklist
At 0.7 MPa, the push force increases to 5497 N.
The rear adjuster screw allows you to shorten the effective travel from the 115 mm nominal stroke down to 40 mm. This creates a 40 to 115 mm usable window, letting you set the exact end-stop at commissioning without changing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.