
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X135-20 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 135mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
It features a 25mm carbon steel rod and a G1/2 PT port. By integrating an external adjusting screw, this model provides a usable travel window of 115-135mm, allowing you to dial back the nominal 135mm stroke by up to 20mm during machine setup.
This fine-tuning capability eliminates the need to swap cylinders or bolt on external stops when aligning end positions. The extruded aluminum barrel includes sensor grooves on both sides, and while this unit omits a magnet, adding an -S suffix enables compatibility with AirTAC CMSE reed and DMSE electronic sensors. SAIJ supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X135-20 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 135 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×135 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly adapt the 115-135mm travel window on packaging lines when switching to different product sizes without changing the cylinder.
Fine-tune the retract stroke by up to 20mm during initial machine commissioning to perfectly align tooling stops.
Provide flexible positioning on automated assembly equipment where the exact end-of-stroke contact point varies between runs.
If your load requires less force, stepping down to an 80mm bore yields 2513N; stepping up to 125mm provides 6136N. Choose the SAIJ adjustable-stroke design over a fixed SAI when you anticipate product changeovers or need to trim the travel window without adding external stops. To match this ISO 15552 cylinder for a replacement, verify the 100mm bore, 135mm stroke, 20mm adjustment, G1/2 port, PT thread, and no magnet.
Because the stroke is 135mm, side-load risks are moderate, but always ensure the 25mm rod and M20x1.5 thread are guided externally if subjected to lateral stresses. Remember that the rear adjuster acts strictly as a travel stop, not a lock; the cylinder will not hold its load without live air. For dead-load holding, consider an AirTAC SAIL or BSAI model.
Quick checklist
At 0.7 MPa, the push force increases to 5497N.
The rear adjuster screw allows you to shorten the effective travel from the nominal 135mm down to 115mm. This creates a 115-135mm adjustable window for fine-tuning the end position without swapping the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.