
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X145-40 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 145mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ100X145-40 is a double-acting ISO 15552 profile cylinder equipped with a rear mechanical adjuster, allowing you to dial back the nominal 145 mm stroke by up to 40 mm. This creates a precise 105-145 mm usable travel window, allowing exact end-position tuning during commissioning without swapping hardware.
This 100 mm bore unit features a carbon steel piston rod with an M20x1.5 thread, paired with a PT tapered G1/2 port to handle high airflow. The extruded aluminum barrel includes sensor grooves on both sides, ready for AirTAC CMSE reed or DMSE electronic switches if a magnet is specified later. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2, deliberately omitting FB, CA, CB, and CR configurations.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X145-40 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 145 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×145 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly adapt a packaging line for different carton lengths by dialing the stroke back within the 105-145 mm window instead of physically swapping cylinders.
Fine-tune the retract end-position during machine commissioning to achieve exact mechanical alignment without adding bulky external stopper blocks.
The SAIJ100X145-40 is selected over a fixed-stroke SAI cylinder when a machine requires variable end-stops or product-size changeovers. The rear screw acts purely as a travel stop for deceleration, not a lock, so it will not hold a load without live air pressure. For dead-pilot load holding, consider an external rod lock or the SAIL series.
When replacing an ISO 15552 cylinder, verify the 100 mm bore, 145 mm stroke, 40 mm adjustment range, PT G1/2 port, and required mounting bracket. Because the stroke is 145 mm, the M20x1.5 rod handles moderate side loads well, but any lengthy unsupported overhang still necessitates an external guide rail to prevent premature seal wear.
Quick checklist
If operating pressure is increased to 0.9 MPa, the push force reaches 7068 N.
The rear adjuster screw acts as a mechanical stop, allowing you to shorten the 145 mm nominal stroke by up to 40 mm. This results in a usable travel window of 105-145 mm, though it only stops the piston and does not lock the load without air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.