
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X155-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 155mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
It features a carbon steel piston rod and PT tapered port threads. By integrating an external stopper at the rear, this model allows you to trim the effective travel back by up to 30 mm, creating a precise 125-155 mm usable stroke window without swapping out the entire actuator.
This adjustability is crucial during machine commissioning or product changeovers, letting you fine-tune the retract end position on the fly. The extruded aluminum barrel includes sensor grooves on both sides, and while this specific SKU lacks a magnet, adding an -S variant enables compatibility with AirTAC CMSE reed and DMSE electronic sensors. The generous 25 mm rod diameter and M20x1.5 rod thread provide excellent resistance to side loads, while the adjustable air cushions at both ends ensure smooth deceleration.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X155-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 155 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×155 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 125-155 mm retract position instantly when switching a packaging line to a different product size, avoiding the need to physically swap cylinders or add spacer shims.
Fine-tune the final resting position of a high-thrust pressing operation during initial setup, using the rear screw to perfect the 3927N clamping depth.
Provide a mechanically adjustable end-stop for automated assembly stations where the exact retraction distance must be tweaked periodically without reprogramming the PLC.
The SAIJ100X155-30 is selected specifically over a fixed-stroke SAI when the exact retract distance needs to be dialed in physically at the machine rather than relying on hard stops. When ordering a replacement, verify the 100 mm bore, 155 mm stroke, 30 mm adjustment range, PT G1/2 port, and mounting style. SAIJ supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, deliberately omitting FB, CA, CB, and CR options.
Because the 155 mm nominal stroke is relatively short, side-load stress is minimal, but always ensure the load is guided externally. Remember that the rear adjuster functions strictly as a travel stop, not a locking device; the cylinder cannot hold a load without live air pressure. For true pneumatic load-holding, consider the SAIL or BSAI series instead.
Quick checklist
If pressure is increased to 0.7 MPa, the push force rises to 5497N.
The rear adjuster screw acts as a mechanical stop, allowing you to shorten the 155 mm nominal stroke by up to 30 mm. This creates a usable travel window of 125-155 mm for fine-tuning the end position at commissioning. Note that this mechanism is a stop, not a lock, and requires live air to hold position.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.