
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X165-40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 165mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ100X165-40-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear mechanical stroke adjuster. It features a 100mm bore and a 165mm nominal stroke that can be dialed back by up to 40mm, providing a precise usable travel window of 125 to 165mm.
This unit includes a standard carbon steel rod and a PT tapered port thread. The -S magnet option enables position sensing with AirTAC CMSE reed and DMSE electronic switches, which seat cleanly into the dual-side sensor grooves on the extruded aluminum barrel. The rear adjuster acts purely as a travel stop for end-position tuning and does not lock the load without live air pressure.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X165-40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 165 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×165 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract position within the 125-165mm window during product size transitions without replacing hardware.
Fine-tune the final stopping point at commissioning to compensate for mechanical wear or sensor drift.
Set precise retract limits on automated assembly lines where multiple stroke endpoints are required.
Select this 100mm bore cylinder when an application requires substantial thrust—3927N at 0.5MPa—along with the flexibility to fine-tune the retract end-position during commissioning without swapping out the cylinder or adding external stops. If your process demands less force, stepping down to an 80mm bore yields 2513N; if you need more power, a 125mm bore provides 6136N. Because the 165mm stroke is under 300mm, side-load stress is moderate, but the robust 25mm rod and M20x1.5 thread handle standard loads effectively.
For a true ISO 15552 replacement match, specify a 100mm bore, 165mm stroke, 40mm adjustment range, PT port threads, and the -S magnet. Note that the SAIJ mounting set is limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR options found on some standard cylinders. If your machine requires holding a load without continuous live air, use a SAIL or BSAI cylinder instead of relying on this adjuster.
Quick checklist
At 0.7MPa, the push force increases to 5497N.
The rear adjusting screw acts as a mechanical stop, allowing you to shorten the effective travel from the nominal 165mm down to 125mm. This provides a 125-165mm adjustable window for fine-tuning the end position without altering the cylinder mount.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.