
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X170-40 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 170mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ100X170-40 is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It provides a 130-170 mm usable travel window, allowing you to dial back the 170 mm nominal stroke by up to 40 mm during machine commissioning.
This model features a 25 mm carbon steel piston rod and an M20x1.5 rod thread, providing excellent rigidity against side loads. The extruded aluminum barrel includes sensor grooves on both sides, ready for AirTAC CMSE reed or DMSE electronic switches if a magnet is added later. Remember that the rear adjuster acts purely as a travel stop for deceleration; it does not hold the load without live air pressure.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X170-40 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract position within the 130-170 mm window when switching product sizes on a packaging line, avoiding the need to physically swap cylinders.
Fine-tune the end-of-stroke deceleration at commissioning by trimming up to 40 mm, working alongside the standard 36 mm air cushions to absorb kinetic energy.
If your force requirements are lower, stepping down to an 80 mm bore yields 3518 N at the same pressure, offering a lighter footprint. The SAIJ100X170-40 is selected over a fixed SAI cylinder when you need an external stop to fine-tune the retract end-position during product changeovers without physically swapping the actuator.
When replacing an ISO 15552 cylinder, match the 100 mm bore, 170 mm stroke, 40 mm adjustment range, G1/2 port, and mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2). Because the 170 mm stroke is below the 300 mm threshold, side-load stress is moderate, but any unsupported load still requires an external guide. For load-holding without live air, the rear stop is insufficient—consider an external rod lock or the AirTAC SAIL/BSAI series instead.
Quick checklist
The rear adjusting screw acts as an external stopper, allowing you to shorten the effective stroke from the 170 mm nominal length down to a minimum of 130 mm. This provides a 130-170 mm usable travel window for fine-tuning the end position without changing the cylinder itself.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.