
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X170-50 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 170mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ100X170-50 is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster, allowing you to dial back the 170 mm nominal travel by up to 50 mm. This creates a highly flexible 120-170 mm usable travel window, letting you fine-tune the retract end position during commissioning without swapping out the physical actuator. In the 100 mm bore class, it delivers substantial thrust, pushing 7068 N and pulling 3681 N at 0.9 MPa.
Unlike a fixed-stroke SAI, this model uses an external stopper screw at the rear to set the travel limit rather than relying on external mechanical stops. The carbon steel piston rod features an M20x1.5 thread, providing a robust interface for mounting attachments. It is important to note that this rear adjuster acts strictly as a travel stop and does not function as a lock; the cylinder cannot hold a load without live air pressure, so a SAIL or BSAI model is required for true load-holding.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X170-50 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 120-170 mm travel window during product size changeovers to set new retract stops without physically replacing the cylinder.
Fine-tune the end-of-stroke position during initial machine setup to perfect timing and mechanical alignment without adding external shims.
If your setup only requires standard fixed travel without the need for commissioning adjustments, the standard AirTAC SAI cylinder is a simpler alternative. Because this is a 170 mm stroke, side-load risks are minimal, but any long unsupported travel still necessitates an external guide to prevent rod wear.
When specifying a replacement, ensure you match the 100 mm bore, 170 mm stroke, and 50 mm adjustment range. The fluid port is PT (tapered) G1/2, and the unit operates at speeds between 30-800 mm/s. Mounting options are limited to the SAIJ subset: Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR footprints found on other variants.
Quick checklist
The 50 mm adjustment screw allows you to shorten the 170 mm nominal stroke, providing a usable travel window of 120 to 170 mm.
No, the rear adjuster acts only as a mechanical travel stop to set the end position and deceleration point. It is not a lock and cannot hold a load without live air pressure. For load-holding without air, consider the AirTAC SAIL or BSAI cylinder series.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.