
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X185-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 185mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ100X185-75 is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear mechanical stroke adjuster. This built-in adjustability allows you to dial in the exact end position at commissioning without physically swapping the cylinder or adding external stops.
This 100mm bore unit uses a G1/2 port and a 25mm carbon steel rod with an M20x1.5 thread, offering high rigidity against side loads. The mounting footprint is dimensionally interchangeable per ISO 15552, utilizing a reduced SAIJ-specific set of attachments (Basic, FA, LB, TC, FTC, TCM1, TCM2) that omits FB, CA, CB, and CR. The extruded aluminum barrel includes dual sensor grooves for mounting CMSE reed or DMSE electronic switches if a magnet is later required.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X185-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 185 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×185 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Rapidly reconfigure the end-of-stroke position on packaging lines when switching to a different product size, using the 75mm adjustment window to avoid physically remounting the cylinder.
Act as a configurable diverter or gate on a conveyor system, allowing operators to fine-tune the 110-185mm travel distance during line setup and commissioning.
Precisely set the lower stopping point for a light-duty pressing or stamping operation, using the rear stopper to guarantee consistent depth without altering the pneumatic pressure.
Select this 100mm bore adjustable cylinder when your application requires heavy thrust (3927N at 0.5 MPa) alongside frequent product-size changeovers, as the 75mm rear stopper screw easily trims the 185mm nominal stroke down to 110mm.
Because the 185mm stroke is below the 300mm threshold, side-load risks are moderate, but the 25mm rod still requires external guidance for heavy lateral loads. The rear adjuster acts strictly as a travel stop and deceleration aid—it does not hold the load without live air pressure. For true fail-safe load holding, specify a SAIL (pneumatic lock) or BSAI (clamp-lock) cylinder, or integrate an external pilot-operated check valve. To match this ISO 15552 replacement exactly, confirm the 185mm stroke, 75mm adjust code, PT tapered G1/2 port, mounting style, and that no -S magnet is present.
Quick checklist
If pressure is increased to 0.9 MPa, the push force reaches 7068N.
The rear adjuster screw acts as a mechanical stop that can shorten the 185mm nominal stroke by up to 75mm, giving a usable travel window of 110-185mm. It allows fine-tuning of the end position at commissioning without swapping cylinders, but it acts only as a stop and does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.