
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X210-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 210mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
Its 210mm nominal stroke can be fine-tuned down by up to 10mm, providing a usable travel window of 200-210mm for precise end-position calibration during machine commissioning. This eliminates the need to swap out the entire cylinder or bolt on external stoppers when dialing in a final position.
This bore features a 25mm carbon steel piston rod with an M20x1.5 thread, paired with a G1/2 PT port and 36mm cushions at both ends. The extruded aluminum barrel includes sensor grooves on both sides, allowing you to add CMSE reed or DMSE electronic switches if position feedback is later required. The rear adjuster acts strictly as a travel stop to set deceleration, meaning it will not hold a load safely without continuous live air pressure.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X210-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 210 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×210 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact end-of-stroke point within a 200-210mm window during machine setup without physically changing the cylinder.
Compensate for minor mechanical drift or tooling wear by adjusting the rear stopper by up to 10mm on the fly.
The 10mm adjustment window is ideal for applications requiring minor mechanical trimming rather than large product changeovers. For fixed-position tasks without any variance, a standard SAI cylinder is sufficient, but the SAIJ variant shines when final dimensions need on-the-fly tweaking.
When replacing an ISO 15552 cylinder, match the 100mm bore, 210mm stroke, G1/2 port, and your required mounting style. SAIJ supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, but omits FB, CA, CB, and CR options. Because the stroke exceeds 300mm only on larger frames, this 210mm unit handles side loads well, though long unsupported rods still necessitate an external guide. Remember that for dead-load holding without air, you must look to the SAIL lock or BSAI clamp-lock series, as this adjuster is not a brake.
Quick checklist
The rear adjuster acts as a mechanical stop that shortens the 210mm nominal stroke by up to 10mm, giving an effective travel range of 200-210mm. It only sets the end position and does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.