
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X600-20 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 600mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
Its 600 mm nominal stroke can be dialed back by up to 20 mm, creating a precise 580-600 mm usable travel window for end-position tuning during commissioning. The extruded aluminum barrel features sensor grooves on both sides for flexible mounting of CMSE reed or DMSE electronic switches if a magnet is added later.
This 100 mm bore unit uses a G1/2 port and a robust 25 mm carbon steel rod with an M20x1.5 thread, providing high side-load resistance for heavy-duty handling. It supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR options found on some standard ISO cylinders.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X600-20 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 580 to 600 mm retract distance during machine setup to accommodate varying material thicknesses without reprogramming the motion controller.
Quickly adjust the stroke end-position on packaging lines when switching between different carton sizes, using the rear screw to fine-tune the travel window.
The adjustable stroke is chosen over a fixed SAI cylinder when you need to fine-tune the retract end-stop during product changeovers without adding external stops or swapping the barrel. For any application with a 600 mm stroke, you must use an external guide to prevent rod binding, as the rear adjuster is a travel stop and not a lock.
To match this ISO 15552 cylinder for a replacement, verify the 100 mm bore, 600 mm stroke, 20 mm adjustment range, PT tapered port threads, and the specific mounting accessory. Because no -S magnet is specified here, position sensing is not possible out of the box. Remember that the rear adjuster and air cushions only decelerate the load; they do not hold position without live air pressure, so consider an AirTAC SAIL or BSAI for load-holding needs.
Quick checklist
At 0.9 MPa the push force is 7068N. The maximum rated force is 801 kgf at 1.0 MPa.
The rear adjuster acts as a stopper that lets you shorten the effective travel by up to 20 mm, creating a 580-600 mm usable window. It allows fine-tuning of the end position at commissioning without swapping the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.