
The AirTAC SAIJ100 Adjustable Cylinder SAIJ100X950-40S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø100mm bore and 950mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ100X950-40-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a 910-950 mm usable travel window by trimming up to 40 mm off the 950 mm nominal stroke. The extruded aluminum barrel includes sensor grooves on both sides, and this -S variant includes a magnet for position detection.
This model uses a carbon steel piston rod with an M20x1.5 thread and G1/2 ports. The rear adjustment screw acts purely as a mechanical stop to fine-tune the retract end position during commissioning without adding external stops. It is not a locking device, so load holding without live air requires an external rod lock or a SAIL cylinder. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2.
| Model | Airtac SAIJ100 Adjustable Cylinder SAIJ100X950-40S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø100 mm |
| Stroke | 950 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | — |
| Max (@1.0 MPa) | 751 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 100 | Bore size in mm. |
| ×950 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract position during product changeovers using the 40 mm rear adjustment screw, avoiding cylinder swaps or external stopper blocks.
Set precise end-stops for large actuators on the assembly line, tuning the 950 mm stroke down to 910 mm to accommodate varying part sizes.
If you need less force, the 80 mm bore provides 2513 N. If you need more, the 125 mm bore offers 6136 N. The adjustable stroke is ideal for machine changeovers where the exact retract distance varies by 40 mm or less, eliminating the need to swap cylinders. To replace this ISO 15552 cylinder, match the 100 mm bore, 950 mm stroke, 40 mm adjustment, G1/2 PT ports, and -S magnet.
Because the 950 mm stroke is long, the M20x1.5 carbon steel rod can carry significant side loads, but an external guide is still recommended to prevent rod bending. The rear adjuster works alongside the variable air cushions at both ends to decelerate the load. For load-holding without live air pressure, use a SAIL pneumatic lock, a BSAI clamp-lock, or an external pilot-operated check valve. Sensors must be AirTAC CMSE reed or DMSE electronic switches.
Quick checklist
At 0.7 MPa, the push force increases to 5497 N.
The rear adjusting screw acts as a mechanical stop that allows you to shorten the effective stroke by up to 40 mm, providing a usable travel window of 910 to 950 mm. It only sets the travel end and does not hold the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.