Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10
The AirTAC SAIJ125 Adjustable Cylinder SAIJ125X425-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø125mm bore and 425mm stroke, G1/2 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ125 mm
- Stroke425 mm
- Port sizeG1/2
- Acting typeDouble acting
- Rod threadM27×2
- CushionAdjustable, 40 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10
The AirTAC SAIJ125X425-10 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to fine-tune the end position. With a 425 mm nominal stroke and a 10 mm adjustment range, it provides a usable travel window of 415-425 mm.
It features a carbon steel piston rod with an M27x2 thread and PT tapered ports. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch placement. Because this is a long-stroke application, the 32 mm rod diameter provides robust support, though an external guide is still recommended to manage side loads.
Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10 Technical Specifications
| Model | Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø125 mm |
| Stroke | 425 mm |
| Acting type | Double acting |
| Port size | G1/2 |
| Rod thread | M27×2 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 40 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø125mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 5734 N | 5734 N |
| 0.7 MPa | 8027 N | — |
| Max (@1.0 MPa) | 1169 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 125 | Bore size in mm. |
| ×425 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10 Is Used
Product Changeovers
Dial in the retract end-position by up to 10 mm during product size transitions without physically swapping the cylinder or repositioning hard stops.
Commissioning Calibration
Fine-tune the end-of-stroke position during initial machine setup to compensate for mechanical tolerance stack-up across the 415-425 mm window.
Is the Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10 the Right Cylinder?
The adjustable stroke is ideal for machine changeovers, allowing you to dial in the exact retract position without adding external mechanical stops.
For a direct replacement, match the 425 mm stroke, 10 mm adjustment, PT port thread, and basic mounting interface. Note that SAIJ uses a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets. The rear adjuster acts only as a travel stop and does not hold the load without live air; for position holding, consider the SAIL or BSAI series.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10 FAQ
The rear adjuster screw lets you shorten the effective stroke by up to 10 mm, creating a 415-425 mm usable travel window. It acts as a mechanical stop to fine-tune the retract position without changing the cylinder itself.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SAI Cylinders
Request a Quote for Airtac SAIJ125 Adjustable Cylinder SAIJ125X425-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.