Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S
The AirTAC SAIJ200 Adjustable Cylinder SAIJ200X35-10S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø200mm bore and 35mm stroke, G3/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
- BoreØ200 mm
- Stroke35 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S
The AirTAC SAIJ200X35-10-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a usable travel window of 25 to 35 mm, allowing you to dial back the 35 mm nominal stroke by up to 10 mm.
Equipped with a standard carbon steel rod and a PT tapered port, this unit includes a magnet for CMSE reed and DMSE electronic sensors. The extruded aluminum barrel incorporates sensor grooves on both sides for flexible switch mounting. The rear adjuster acts purely as a travel stop for end-position tuning and does not hold the load without live air pressure.
Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S Technical Specifications
| Model | Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø200 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15080 N | 15080 N |
| 0.7 MPa | 21111 N | — |
| Max (@1.0 MPa) | 3075 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 200 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S Is Used
Variable End-Stop Forming
Dial in the exact 25 to 35 mm travel window during machine setup to accommodate material thickness variations without swapping out the cylinder.
Short-Stroke Clamping
Holds massive workpieces securely during machining operations, using the rear stopper to quickly adjust the clamping position for different part sizes.
Is the Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S the Right Cylinder?
If you need less force, stepping down to a 160 mm bore yields 10053 N at the same pressure. Choose the SAIJ adjustable-stroke design over a fixed SAI model when you need to fine-tune the retract end-position during commissioning or product changeover without adding external stops.
For load-holding without continuous air pressure, this cylinder is insufficient because the rear adjuster is a stop, not a lock; you would need an SAIL or BSAI cylinder instead. This SAIJ200X35-10-S uses a PT port, supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, and carries the -S magnet option. Since the 35 mm stroke is short, side-load concerns are minimal, but the robust 40 mm rod handles high stresses effectively.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (FA/FB/CA/CB/LB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S FAQ
It can reach up to 3204 kgf at its maximum 1.0 MPa pressure rating.
The rear adjuster screw allows you to shorten the 35 mm nominal stroke by up to 10 mm, creating a usable travel window of 25 to 35 mm. This stopper fine-tunes the end position at commissioning but does not lock the load without live air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SAI Cylinders
Request a Quote for Airtac SAIJ200 Adjustable Cylinder SAIJ200X35-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.