
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X105-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 105mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X105-75 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to fine-tune the effective travel down from a 105 mm nominal stroke. With the 75 mm adjustment screw, you can dial the usable stroke window anywhere between 30 mm and 105 mm without swapping the hardware.
It features a 16 mm carbon steel rod and M12x1.25 rod thread, paired with PT G1/4 ports. The extruded aluminum barrel includes sensor grooves on both sides for direct mounting of CMSE reed or DMSE solid-state switches. SAIJ mounting options are limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR variants found on other series.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X105-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 105 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×105 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact end position during machine commissioning across a 30-105 mm window, avoiding the need to machine external spacers or swap cylinders for minor position shifts.
Quickly adapt the stroke length on packaging lines when running different carton sizes, using the 75 mm rear adjuster to set new retract distances on the fly.
Refine the travel endpoint on test fixtures to prevent overtravel during delicate assembly operations, relying on the 16 mm rod to handle moderate side loads.
Choose this 40 mm bore if you need a highly flexible end-position setup for frequent product changeovers, as the 75 mm adjuster provides an exceptionally wide 30-105 mm travel window. If you need more power, a 50 mm bore provides 982 N.
When replacing an ISO 15552 cylinder, match the 40 mm bore, 105 mm stroke, 75 mm adjustment, PT G1/4 port, and your required mounting kit. Because the rear screw acts only as a mechanical stop and the air cushions manage deceleration, this cylinder will not hold a load without live air pressure; for dead-load holding, consider the SAIL or BSAI series instead.
Quick checklist
At the maximum 1.0 MPa pressure, it can deliver up to 128 kgf.
The rear adjuster screw acts as a mechanical stop that lets you shorten the 105 mm nominal stroke down to a minimum of 30 mm. It only sets the travel end position and does not lock or hold the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.