
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X110-40 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 110mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X110-40 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a nominal 110 mm stroke that can be fine-tuned down by up to 40 mm, yielding a precise 70-110 mm usable travel window for exact end-position calibration.
This extruded aluminum profile cylinder includes sensor grooves on both sides for flexible switch mounting. It uses a standard carbon steel piston rod and a PT tapered port thread. The rear adjuster acts purely as a travel stop for deceleration and positioning, meaning it will not hold a load without continuous live air pressure.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X110-40 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 110 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 70-110 mm travel window during format changes on a packaging line, using the rear stopper to set exact end positions without swapping cylinders.
Fine-tune the retraction point during initial commissioning to perfectly align pick-and-place heads, avoiding the need for external mechanical shims.
Handle multiple part sizes on the same fixture by adjusting the effective stroke up to 40 mm, providing flexible positioning for mid-range 628 N loads.
The adjustable 70-110 mm window is ideal for machine setups requiring frequent product changeovers, allowing you to dial in the exact end-stop without swapping hardware or adding external stops. For fixed travel needs without commissioning tweaks, the standard SAI cylinder is a simpler alternative.
To replace an ISO 15552 cylinder, match the 40 mm bore, 110 mm stroke, 40 mm adjustment range, PT port threads, and your required mounting hardware. Note that SAIJ supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts, but omits FB, CA, CB, and CR brackets. Since the stroke is 110 mm, side-load is minimal, but always guide the load externally for optimal bearing life.
Quick checklist
If you increase pressure to 0.7 MPa, the push force rises to 879 N.
The rear adjuster screw lets you trim the effective travel back by up to 40 mm from the 110 mm nominal stroke, creating a 70-110 mm usable window. It functions as a mechanical stop for end-position tuning, not a lock, and cannot hold a load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.