
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X115-40 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 115mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X115-40 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a nominal 115 mm stroke with a 40 mm adjustment range, creating a usable travel window of 75-115 mm for precise end-position tuning during machine commissioning.
This model uses a carbon steel piston rod with an M12x1.25 thread and PT tapered port threads. The extruded aluminum barrel includes sensor grooves on both sides, allowing you to add CMSE reed or DMSE electronic sensors if position feedback is needed later. It features variable air cushions at both ends to manage end-of-stroke impact.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X115-40 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 115 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×115 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 75-115 mm travel window during product size changes to set exact clamping or positioning depths without replacing hardware.
Fine-tune the retract end-position at startup to absorb mechanical tolerances and dial in the exact 40 mm stroke trim.
Adjust the stroke end-point on the fly for conveyor sorting arms that handle varying package sizes.
Choose this adjustable-stroke cylinder when your setup requires exact end-stop tuning without swapping out the physical cylinder or adding external stops. For lighter duty, a 32 mm bore provides 402 N. Remember that the rear adjuster acts as a travel stop, not a lock; this plain SAIJ cylinder will not hold a load without live air pressure, so consider an SAIL or BSAI cylinder for fail-safe load holding.
For ISO 15552 dimensionally interchangeable replacements, match the 40 mm bore, 115 mm stroke, 40 mm adjustment range, PT port threads, and your required mounting interface. SAIJ supports a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2, but omits FB, CA, CB, and CR brackets. Since the 115 mm stroke is under 300 mm, side-load stress is minimal, but always ensure the M12 rod thread is properly aligned to prevent premature seal wear.
Quick checklist
At the maximum operating pressure of 1.0 MPa, it delivers up to 128 kgf.
The rear adjuster screw lets you shorten the effective travel from the nominal 115 mm down to 75 mm. This creates a 75-115 mm adjustable window for fine-tuning the retract end-position without external stops.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.