
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X150-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 150mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X150-100 is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. By integrating an external stopper at the rear, this model allows you to mechanically shorten the effective travel from its 150mm nominal length down to as little as 50mm, creating a highly versatile 50-150mm usable window.
This wide adjustment range is ideal for product changeovers, letting you fine-tune the retract end position at commissioning without swapping the cylinder or adding external stops. The extruded aluminum barrel features sensor grooves on both sides for CMSE or DMSE switches, though this specific SKU is configured without a magnet. Remember that the rear adjuster acts purely as a travel stop and does not hold the load without live air pressure.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X150-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact retract distance for different packaging lengths using the 50-150mm window, eliminating the need to physically swap cylinders during line format changes.
Fine-tune the end-of-stroke position during machine setup to perfect pick-and-place coordinates without machining new hard stops or altering the ISO 15552 mounting footprint.
Choose this 40mm bore when you need a broad 50-150mm adjustable travel window on a single unit, avoiding the need to stock multiple fixed-stroke SAI cylinders for varying product sizes. Because the 150mm stroke is below the 300mm threshold, side-load stress is moderate, but the 16mm rod still requires alignment to prevent premature seal wear.
For an exact ISO 15552 replacement, match the 40mm bore, 150mm nominal stroke, 100mm adjustment range, PT port thread, and carbon steel rod. Note that the SAIJ mounting set is limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR brackets. If your machine requires true load-holding without continuous air pressure, you must use an external rod lock or switch to an AirTAC SAIL or BSAI cylinder, as the SAIJ adjuster is not a brake.
Quick checklist
At 0.7 MPa, the push force increases to 879N.
The rear adjuster acts as a mechanical stop that allows you to shorten the 150mm nominal stroke by up to 100mm, providing a usable travel window of 50 to 150mm. It sets the end position but does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.