
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X155-30S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 155mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X155-30-S is a double-acting ISO 15552 profile cylinder equipped with a rear stroke adjuster. By turning the rear stopper screw, you can trim the effective travel back by up to 30 mm, creating a usable stroke window of 125 to 155 mm for precise commissioning.
This model uses a standard carbon steel rod with an M12x1.25 thread and a PT tapered port for reliable pneumatic connections. It incorporates variable air cushions at both ends to decelerate the load smoothly. The extruded aluminum barrel includes sensor grooves on both sides, allowing you to mount CMSE reed or DMSE solid-state switches exactly where needed along the travel path.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X155-30S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 155 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×155 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly adapt the end-stop position within the 125-155 mm window when switching between product sizes on a shared production line.
Fine-tune the final retract position during initial setup without machining new spacer blocks or replacing the entire actuator.
Dial in the exact clamping or pressing distance by trimming up to 30 mm off the nominal stroke to accommodate material thickness variations.
Select this 40 mm bore cylinder when your application requires an output force of 628N (push) or 528N (pull) at 0.5 MPa, and you need to dial in the end-of-stroke position during machine setup. If you need higher thrust, stepping up to the 50 mm bore yields 982N, while dropping to a 32 mm bore reduces the push force to 402N. The adjustable rear stopper lets you fine-tune the 125-155 mm travel window without swapping the cylinder or adding external mechanical stops, which is invaluable during product changeovers.
As an ISO 15552 profile cylinder, it is dimensionally interchangeable with other ISO 15552 cylinders and uses a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting FB, CA, CB, and CR brackets. The rear adjuster acts only as a travel stop to set deceleration; it does not hold the load without live air pressure. For load-holding requirements without continuous air, consider an AirTAC SAIL or BSAI cylinder. This SAIJ40X155-30-S variant includes a magnet (-S) for CMSE and DMSE sensors and features PT threaded ports.
Quick checklist
At the maximum pressure of 1.0 MPa, the push force reaches 128 kgf.
The rear adjuster screw acts as a mechanical stop that can shorten the effective stroke by up to 30 mm. This creates an adjustable travel window between 125 mm and 155 mm, allowing you to set the exact retract end-position during commissioning without replacing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.