
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X155-50 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 155mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X155-50 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a 155 mm nominal stroke that can be dialed back by up to 50 mm, giving you a usable travel window of 105 to 155 mm to perfectly dial in end positions during commissioning.
The carbon steel piston rod features an M12x1.25 thread, and the body uses a PT tapered G1/4 port. Unlike fixed-stroke SAI models, this rear stopper screw lets you trim the retract position without adding external stops or swapping the cylinder. The adjuster acts purely as a travel stop and works alongside standard air cushions at both ends, but it does not hold the load without live air pressure.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X155-50 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 155 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×155 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly adapt the retract end-stop from 105 to 155 mm when switching between product sizes on a packaging line, avoiding physical cylinder swaps.
Fine-tune the final resting position during machine setup to achieve exact alignment, using the rear screw rather than shimming external stops.
Adjust the pusher travel distance on the fly to accommodate different package widths without altering the pneumatic plumbing.
Select this 40 mm bore when an application requires precise end-position tuning without changing the physical cylinder, yielding a 105-155 mm adjustable travel window. If you need less force, stepping down to a 32 mm bore yields 402 N at 0.5 MPa, while moving up to a 50 mm bore provides 982 N for heavier loads. Because the stroke is 155 mm, side-load stress is moderate, but always ensure external guiding if the load is offset.
For an exact ISO 15552 replacement, match the 40 mm bore, 155 mm nominal stroke, 50 mm adjustment range, PT G1/4 port, and carbon steel rod. Note that SAIJ supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR. Since no lock valve is present, use a SAIL or BSAI cylinder if the load must be held without continuous air pressure.
Quick checklist
At 0.7 MPa, the push force increases to 879 N.
The rear adjuster screw allows you to shorten the 155 mm nominal stroke by up to 50 mm, creating a usable travel window of 105 to 155 mm. This stopper only sets the end position and does not lock the load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.