
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X165-75 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 165mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X165-75 is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. By dialing the external stopper screw, you can trim the nominal 165 mm travel back by up to 75 mm, creating a wide 90-165 mm usable stroke window. This allows precise end-position tuning at commissioning without swapping the barrel or adding external stops. The extruded aluminum profile includes sensor grooves on both sides for flexible switch placement.
The larger rod diameter handles side loads better than smaller bores, though long unsupported strokes still require an external guide. It features PT tapered G1/4 ports, variable air cushions at both ends (30 mm cushion length), and operates at speeds of 30-800 mm/s.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X165-75 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 165 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×165 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 90 to 165 mm travel distance during machine commissioning to perfect positioning without machining external stop blocks.
Quickly adapt a packaging line to different carton lengths by adjusting the rear stroke screw rather than replacing the entire cylinder.
Fine-tune the retract end position to compensate for mechanical wear or slight misalignments over the equipment lifecycle.
Choose this SAIJ40X165-75 when your machine setup requires variable end-stops or frequent product-size changeovers that demand a flexible travel window. If your application needs less push force, stepping down to a 32 mm bore yields 402 N at 0.5 MPa; if you need significantly more clamping power, stepping up to a 50 mm bore provides 982 N. The rear adjuster acts purely as a travel stop and does not hold the load without live air pressure—use an external rod lock, pilot-operated check valve, or AirTAC SAIL/BSAI cylinders for fail-safe load holding.
To match this ISO 15552 replacement exactly, verify the 40 mm bore, 165 mm nominal stroke, 75 mm adjustment range, PT G1/4 port thread, and the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2—omitting FB, CA, CB, and CR). Because this SKU lacks the -S magnet suffix, it will not work with AirTAC CMSE reed or DMSE electronic sensors without modification.
Quick checklist
At 0.9 MPa, the push force increases to 1130 N.
The rear adjuster screw acts as a mechanical stop that lets you shorten the effective stroke from its 165 mm nominal length down to 90 mm. It sets the travel end and relies on the air cushion for deceleration, but it is not a lock and will not hold the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.