
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X170-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 170mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X170-50-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. It provides a nominal 170 mm stroke that can be fine-tuned down by up to 50 mm, yielding a usable travel window of 120-170 mm.
This -S variant includes a magnet for position sensing and uses a standard carbon steel rod with PT tapered port threads. The extruded aluminum barrel features sensor grooves on both sides, allowing you to easily mount CMSE reed or DMSE electronic solid-state switches exactly where your process requires them.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X170-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 170 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×170 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 120-170 mm travel window rapidly when switching between product sizes on a packaging line, ensuring precise end-stops without mechanical rebuilds.
Fine-tune the pressing position during cell setup.
Adjust the retract position on the fly for diverter gates or sorting mechanisms, using the rear screw to set the exact 120 to 170 mm stroke needed.
Select this 40 mm bore when an application demands precise end-position tuning during commissioning or product changeover, avoiding the need to swap cylinders or bolt on external stops. If your setup requires less force, stepping down to a 32 mm bore yields 563 N at 0.7 MPa; for heavier loads, a 63 mm bore provides 2182 N. Since the nominal stroke is 170 mm, an external guide is recommended for optimal side-load management.
The rear adjuster acts strictly as a travel stop and works alongside the standard air cushions to decelerate the piston, but it cannot hold a load without live air pressure. For drop-prevention or dead-load holding, integrate an external pilot-operated check valve or select an AirTAC SAIL or BSAI locking cylinder. To match this ISO 15552 footprint exactly, specify: 40 mm bore, 170 mm stroke, 50 mm adjustment, PT port, Basic/FA/LB/TC/FTC/TCM1/TCM2 mounting, and a magnet.
Quick checklist
The rear adjuster screw allows you to shorten the effective travel from the nominal 170 mm down to 120 mm. It functions as a mechanical stop to set the end position, but it is not a lock and will not hold the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.