
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X180-30S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 180mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X180-30-S is a double-acting, double-rod profile cylinder dimensionally interchangeable per ISO 15552. It features a rear-mounted adjusting screw that allows you to fine-tune the effective stroke, providing a usable travel window of 150-180mm for this 180mm nominal stroke unit. Equipped with a PT tapered port thread and a standard carbon steel rod, it also includes a magnet (-S) for use with CMSE reed and DMSE electronic sensors.
Because the SAIJ is a profile cylinder with an extruded aluminum barrel, it integrates sensor grooves on both sides for straightforward switch mounting. The rear adjuster functions strictly as a travel stop to set deceleration and end-positions accurately during commissioning. It does not hold the load without live air pressure; for true load-holding, a SAIL or BSAI variant is required. This model supports a speed range of 30-800mm/s and uses adjustable air cushions at both ends to manage impact energy.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X180-30S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 150 to 180mm travel needed during machine commissioning or product size changes without replacing hardware.
Use the 30mm rear adjustment screw to fine-tune the retract end-position precisely, accommodating multiple product formats on one line.
Choose this 40mm bore adjustable-stroke cylinder when your application requires precise end-position tuning at commissioning or during product changeover without swapping out the entire cylinder or adding external stops. The 16mm rod and M12x1.25 rod thread offer robust resistance to side loads, though any stroke of 180mm still benefits from an external guide to prevent rod binding.
This SAIJ40X180-30-S configuration includes a PT tapered port, a standard carbon steel rod, and a magnet for CMSE / DMSE sensors. It utilizes the standard SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting the FB, CA, CB, and CR options. For fixed-stroke requirements without the rear adjuster, the standard SAI series is the direct alternative.
Quick checklist
At 0.7MPa, the push force increases to 879N.
The rear adjuster acts as a travel stop, allowing you to shorten the 180mm nominal stroke by up to 30mm. This creates a usable travel window of 150-180mm to fine-tune the end position without adding external stops.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.