
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X185-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 185mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X185-10 is a double-acting, double-rod ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a 175-185 mm usable travel window, allowing you to dial back the 185 mm nominal stroke by up to 10 mm during commissioning. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch mounting.
This model uses a standard carbon steel piston rod with an M12x1.25 thread and a PT tapered port. It features variable air cushions at both ends, 30 mm of cushion travel, and operates at speeds of 30-800 mm/s. The rear adjuster acts purely as a mechanical stop for end-position tuning; it does not hold the load without live air pressure.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X185-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 185 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×185 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Fine-tune the retract end position within a 175-185 mm window during machine commissioning without installing external stopper blocks.
Quickly adjust the effective travel distance on a packaging line when handling slightly different product sizes on the same conveyor.
Dial in the exact 10 mm adjustment range needed for delicate assembly operations where a fixed 185 mm stroke would overshoot the target.
Choose this adjustable-stroke variant when you need fine end-position tuning at machine setup or product changeover without swapping the cylinder or adding external stops. Because the stroke is under 300 mm, side-load stress is manageable, but long unsupported strokes still require an external guide.
To replace an ISO 15552 cylinder, match the 40 mm bore, 185 mm stroke, 10 mm adjustment range, PT port, and mounting choice. SAIJ supports a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR. For load-holding without live air, consider the SAIL or BSAI series, as this adjuster is not a lock.
Quick checklist
At 0.7 MPa, the push force increases to 879 N.
The rear adjusting screw acts as a mechanical stopper, allowing you to trim the effective travel back from the 185 mm nominal stroke to anywhere within a 175-185 mm window. It only sets the travel end and does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.