
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X200-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 200mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X200-30 is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. The extruded aluminum barrel features sensor grooves on both sides, and because no magnet is specified here, you would add an -S suffix if you later need CMSE reed or DMSE electronic solid-state sensors.
This adjustable model uses a PT tapered port (G1/4) and a 16 mm carbon steel rod with an M12x1.25 thread. The rear stopper acts purely as a travel end-deceleration point, not a load lock, meaning live air pressure is required to hold position. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2, deliberately omitting FB, CA, CB, and CR configurations.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X200-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly adjust the 170-200 mm travel window to accommodate different product sizes on the same line without physically replacing the cylinder.
Fine-tune the retract end position during initial commissioning to dial in exact stopping points for precision assembly tasks.
Provide adjustable physical stops for diverter gates or pushing mechanisms where the exact stroke length may vary slightly between batches.
An adjustable stroke is ideal for product changeovers or fine-tuning end positions without swapping the cylinder or adding external stops. If your process requires holding a load without continuous air pressure, consider the SAIL (air-released lock) or BSAI (clamp-lock) variants instead, as the SAIJ adjuster is only a stop.
For an exact ISO 15552 replacement, match the 40 mm bore, 200 mm stroke, 30 mm adjustment range, PT port thread, and your required mounting bracket. Because the stroke is 200 mm, ensure adequate external guiding if the load is heavy or subject to side loads, as the 16 mm rod handles moderate bending moments but cannot support high lateral forces alone.
Quick checklist
At 0.9 MPa, the push force increases to 1130N.
The rear adjuster screw allows you to shorten the effective travel from the nominal 200 mm down to a minimum of 170 mm. This creates a 170-200 mm adjustable window for fine-tuning the end position without changing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.