
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X200-50 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 200mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X200-50 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to trim the nominal 200 mm travel back by up to 50 mm. This creates a precise 150-200 mm usable window, letting you dial in the exact retract end-position during commissioning without swapping out the physical actuator.
Unlike a fixed-stroke SAI cylinder, this model integrates a mechanical stopper at the rear cap to fine-tune the travel limit on product changeovers. The adjuster acts solely as a travel stop and works alongside the standard variable air cushions at both ends; it does not hold the load without live air pressure. The extruded aluminum barrel includes dual sensor grooves, and you can fit position feedback later using AirTAC CMSE reed or DMSE electronic sensors if needed.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X200-50 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Rapidly adjust the 150-200 mm stroke window during product size changeovers to set new end positions without physically swapping cylinders or adding external stopper blocks.
Fine-tune the retract stroke during initial commissioning to dial in exact clamping or positioning distances, absorbing mechanical tolerances directly at the rear screw.
Act as a configurable end-stop on a conveyor sorting line, allowing operators to quickly shorten the travel by up to 50 mm to accommodate different package sizes.
The adjustable 50 mm window is ideal for machines that process varying product sizes, allowing you to shift the end-stop on the fly instead of adding external physical stops. Because the 200 mm stroke exceeds the 300 mm side-load threshold, ensure you use an external guide to support the 16 mm rod and prevent binding during extension.
When specifying a replacement, verify the 200 mm stroke, 50 mm adjustment range, PT (tapered) G1/4 port, and carbon steel rod material. This SAIJ cylinder uses a reduced mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) and omits FB, CA, CB, and CR brackets. Remember that the rear adjuster is not a locking device; for load-holding without live air, select an AirTAC SAIL or BSAI cylinder instead.
Quick checklist
If you increase the pressure to 0.7 MPa, the push force rises to 879 N.
The rear adjuster screw lets you mechanically shorten the 200 mm nominal stroke by up to 50 mm, providing a usable travel window of 150 to 200 mm. It functions as a physical stop to set the end position and is not a lock, meaning it will not hold the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.