
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X200-75S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 200mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X200-75-S is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster. The extruded aluminum barrel includes sensor grooves on both sides for flexible switch mounting.
With a nominal 200mm stroke and a 75mm adjustment range, this model provides a wide 125-200mm usable travel window. This allows operators to dial back the retract end-position for fine-tuning during commissioning or product-size changeovers without swapping the cylinder or adding external stops. It uses a PT tapered port and a 16mm carbon steel rod with an M12x1.25 thread, offering robust side-load resistance for general automation.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X200-75S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly reconfigure the retract end-position from 200mm down to 125mm when switching product sizes on a packaging line, eliminating the need to physically swap cylinders.
Fine-tune the stroke during initial setup to hit exact datum points without machining external stopper blocks or compromising the 30mm cushion length.
Adjust the travel window on the fly for multi-format assembly fixtures, using the 16mm rod and M12x1.25 thread to handle moderate side loads accurately.
If your process needs less force, stepping down to a 32mm bore yields 563N; if higher force is required, a 50mm bore provides 1374N. The adjustable rear stopper is ideal for setups requiring frequent position changes versus a fixed-stroke SAI cylinder.
Remember that the rear adjuster functions strictly as a travel stop, not a lock; it cannot hold a load without live air pressure. For true load-holding, consider an SAIL pneumatic lock or BSAI clamp-lock cylinder. This SAIJ model uses a PT port thread and supports a reduced mounting set of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR brackets.
Quick checklist
The rear adjuster screw allows you to shorten the effective stroke by up to 75mm from the 200mm nominal length, creating a 125-200mm usable travel window. The adjuster acts only as a mechanical stop for deceleration and does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.