
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X270-75S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 270mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X270-75-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to fine-tune the end position. With a nominal 270 mm stroke and a 75 mm adjustment range, it provides a highly flexible 195-270 mm usable travel window. This makes it ideal for adapting to varying product sizes on a production line without swapping out the entire actuator.
The 16 mm rod and M12x1.25 thread provide robust resistance to side loads, though the 270 mm stroke means an external guide is still recommended for heavily offset loads. Unlike a fixed-stroke SAI, this model's rear mechanical stopper lets you dial in the retract position during commissioning. The adjuster and the variable air cushions at both ends decelerate the load, but neither acts as a lock; for position holding without live air pressure, consider an external pilot-operated check valve or the SAIL lock series.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X270-75S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 270 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×270 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly adapt the retract end-stop for different part lengths on a single machine bed without disassembling the pneumatic setup.
Fine-tune the 195-270 mm travel window during initial setup to perfectly time the pick-and-place motion without adding external shims.
Adjust the stroke on the fly to push varying box sizes onto a packaging line, ensuring consistent positioning every time.
Choose this 40 mm bore when you need slightly more force than the 32 mm version (402 N at 0.5 MPa) but want to avoid the bulk of a 50 mm cylinder (982 N at 0.5 MPa). The adjustable stroke is selected over a fixed SAI when a machine requires frequent product changeovers, allowing the end-stop to be reconfigured on the fly. To replace an ISO 15552 cylinder, match the 40 mm bore, 270 mm stroke, 75 mm adjustment, PT G1/4 port, and the -S magnet requirement.
Because the stroke is 270 mm, the unsupported rod length increases bending risk. Always use an external linear guide to prevent excessive radial loads. The mounting interface supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 brackets, omitting FB, CA, CB, and CR options.
Quick checklist
At the maximum 1.0 MPa pressure, it can deliver up to 128 kgf of push force.
The rear adjuster screw acts as a mechanical stop, allowing you to shorten the effective travel from the nominal 270 mm down to as little as 195 mm. This creates a 195-270 mm usable window for fine-tuning the end position at commissioning.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.