
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X280-40 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 280mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X280-40 is a double-acting, double-rod ISO 15552 profile cylinder equipped with a rear stroke adjuster.
This model incorporates a 16mm carbon steel rod with an M12x1.25 thread, providing a robust interface for standard attachments. The extruded aluminum barrel includes sensor grooves on both sides for flexible mounting of CMSE or DMSE switches, and the approved mounting set includes Basic, FA, LB, TC, FTC, TCM1, and TCM2.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X280-40 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 280 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×280 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 240-280mm end-stop during initial commissioning to accommodate mechanical tolerances without machining external spacers.
Quickly adjust the retract position by up to 40mm on a packaging line when switching to a different product size.
Fine-tune the stroke end on automated test fixtures to ensure precise contact without relocating the cylinder mounting.
Choose this adjustable-stroke model when your application requires fine end-position tuning during setup or product changeover without swapping out the entire cylinder or adding external stops. If you need less force, stepping down to a 32mm bore yields 402N at 0.5 MPa, while stepping up to a 50mm bore provides 982N for heavier loads.
Because the 280mm stroke exceeds the 300mm threshold, ensure an external guide supports the load to prevent excessive side-loading on the rod. Remember that the rear adjuster acts only as a travel stop, not a lock; this SAIJ cylinder will not hold its position without live air pressure, so consider SAIL or BSAI variants if load-holding is required. For an exact ISO 15552 replacement, match the 40mm bore, 280mm stroke, 40mm adjustment, PT tapered port, and carbon steel rod.
Quick checklist
The rear adjuster screw allows you to mechanically shorten the effective stroke by up to 40mm from the 280mm nominal length, providing a usable travel window of 240-280mm. The adjuster acts as a physical stop and does not lock the load without live air pressure.
The cylinder operates at speeds between 30 and 800 mm/s and features variable air cushions at both ends to decelerate the load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.