
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X375-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 375mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
It features a 16mm carbon steel piston rod and a PT G1/4 port. By integrating an external adjusting screw, this model provides a usable travel window of 365-375mm, allowing you to trim the effective stroke by up to 10mm without swapping out the entire unit.
Because the nominal 375mm stroke is relatively long for this bore size, the 16mm rod diameter should be paired with an external guide to prevent excessive side-loading and premature seal wear. The extruded aluminum barrel includes sensor grooves on both sides for straightforward switch placement. Mounting options are limited to the SAIJ subset—Basic, FA, LB, TC, FTC, TCM1, and TCM2—omitting the FB, CA, CB, and CR brackets found on other variants.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X375-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 375 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×375 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 365 to 375mm retract position during initial setup to align tooling perfectly without machining custom spacers.
Quickly adjust the end-stop by up to 10mm on packaging lines when switching between slightly different product sizes.
Precisely position pushes or diverts on a conveyor, using the rear screw to fine-tune the resting state of the actuator.
The adjustable 10mm window is ideal for fine-tuning the retract end position during machine commissioning or product changeovers, eliminating the need to bolt on external stops. For strokes of 375mm or more, always support the load with an external guide rail to protect the cylinder from side-load forces.
When specifying a replacement, verify the 40mm bore, 375mm stroke, 10mm adjustment range, PT G1/4 port, and the required mounting bracket. Note that the rear adjuster functions strictly as a travel stop and does not hold the load without continuous air pressure; for true load-holding, consider the SAIL or BSAI series instead.
Quick checklist
The rear adjuster acts as a mechanical stop that lets you shorten the nominal 375mm stroke by up to 10mm, providing an effective travel range of 365-375mm. It only sets the end position and does not lock the load without live air pressure.
At 0.7 MPa, the push force increases to 879N.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.