
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X40-20S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 40mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X40-20-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to trim the nominal 40 mm travel back by up to 20 mm. This creates a highly flexible 20 to 40 mm usable stroke window, enabling precise end-position tuning at commissioning without swapping out the physical cylinder.
Because this is an adjustable-stroke variant, the rear screw functions strictly as a mechanical stop to set the retract end position and deceleration point; it does not hold the load without live air pressure. For load-holding without continuous pressure, you would need a SAIL pneumatic lock or an external rod lock. This -S model includes a magnet for position sensing via CMSE reed or DMSE electronic switches.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X40-20S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact end position during initial commissioning using the 20-40 mm travel window, avoiding the need to machine custom external spacers.
Quickly adapt the retract stop for different product sizes on a conveyor line by turning the rear adjuster screw.
Set precise mechanical limits for light pressing or forming tasks that require a adjustable reach within a 20 mm range.
Select this 40 mm bore model when your application requires fine-tuning the end-of-stroke position during machine setup or product changeover, rather than relying on a fixed-stroke SAI cylinder. To ensure a true ISO 15552 replacement match, verify your bore, 40 mm nominal stroke, 20 mm adjustment range, PT port thread, and required mounting bracket (Basic, FA, LB, TC, FTC, TCM1, or TCM2). The SAIJ series omits the FB, CA, CB, and CR mounts.
The 16 mm rod diameter and M12x1.25 rod thread provide robust resistance to side loads, but because the 40 mm stroke is relatively short, you likely will not need an external guide rail. The integrated adjustable air cushions at both ends work alongside the rear stopper to prevent hard impacts, but remember that neither the cushion nor the adjuster acts as a brake.
Quick checklist
At the maximum 1.0 MPa pressure, it can deliver up to 128 kgf.
The rear adjusting screw acts as a mechanical stopper that lets you shorten the nominal 40 mm stroke by up to 20 mm, creating a usable travel window of 20 to 40 mm. It sets the end position but does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.