
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X40-30S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 40mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
Because this SKU carries a 30mm adjustment code on a 40mm nominal stroke, technicians can dial the effective travel down to a 10mm minimum, creating a highly versatile 10-40mm usable window for short-stroke clamping or pressing. The included magnet (-S) enables direct position feedback using AirTAC CMSE reed or DMSE electronic sensors housed in the dual-side barrel grooves.
Unlike a fixed-stroke SAI, this adjustable variant allows you to fine-tune the retract end-position at commissioning without swapping hardware or adding external stops. The carbon steel rod features an M12x1.25 thread, and the rear adjuster functions strictly as a travel stop to set deceleration, meaning it will not hold a load without continuous live air pressure.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X40-30S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 40 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 10-40mm stroke window during format changes to accommodate different package heights without swapping the cylinder.
Provides 628N of precise pressing force at 0.5 MPa, with the rear stopper allowing exact end-position tuning for delicate assembly tasks.
The integrated magnet works with DMSE electronic sensors to confirm clamp positions, while the adjuster sets the exact travel limit.
The adjustable 10-40mm travel window is ideal for machines that process varying product sizes and need rapid changeovers without mechanical redesign. For load-holding without live air, this adjuster will not act as a lock; you should integrate an external pilot-operated check valve or select an AirTAC SAIL or BSAI cylinder instead.
To match this exact ISO 15552 footprint for a direct replacement, specify a 40mm bore, 40mm nominal stroke, 30mm adjustment range, PT tapered port thread, and a magnet for CMSE/DMSE sensors. The mounting hardware is limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR options.
Quick checklist
At 0.7 MPa, the push force increases to 879N.
The rear adjuster screw allows you to trim the 40mm nominal stroke by up to 30mm, providing an effective travel window of 10-40mm. It acts as a mechanical stop to set the end position and does not lock the load without air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.