
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X400-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 400mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
Its 400 mm nominal stroke can be dialed back by up to 100 mm, creating a 300-400 mm usable travel window. This allows precise end-position tuning at commissioning without swapping hardware. It features a carbon steel piston rod and PT tapered ports.
The rear adjuster acts strictly as a mechanical stop to set the retract position and is not a locking device. For position holding without live air pressure, external pilot-operated check valves or a related SAIL lock cylinder are required. This extruded aluminum profile cylinder supports standard AirTAC CMSE and DMSE sensors via grooves on both sides.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X400-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 300-400 mm travel window during format size changes on a packaging line without physically replacing the cylinder.
Fine-tune the retract end-position during initial setup to perfectly align tooling, avoiding the need for external shims.
Adjust the stroke on a diverter gate to handle different package sizes dynamically on the fly.
Choose this 40 mm bore when an application requires moderate thrust and a highly variable end-stop, as opposed to a fixed-stroke SAI cylinder. If your setup needs less force, stepping down to a 32 mm bore yields 402 N at 0.5 MPa; stepping up to a 50 mm bore provides 982 N. Because this model features a 400 mm stroke, an external guide is recommended to support the load and mitigate side-loading on the 16 mm rod.
To match this ISO 15552 dimensionally interchangeable cylinder, confirm the 400 mm stroke, 100 mm adjustment range, PT port threads, and your required mounting set. The SAIJ series uses a reduced mounting selection of Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting FB, CA, CB, and CR options. This specific configuration includes a standard carbon steel rod and no magnet.
Quick checklist
At 0.7 MPa, the push force increases to 879 N.
The rear adjuster screw acts as a mechanical stop, allowing you to shorten the effective travel from the 400 mm nominal stroke down to 300 mm. It sets the end position but does not lock the load without live air.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.