
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X475-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 475mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X475-50-S is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to fine-tune the travel window between 425 and 475 mm. The integrated -S magnet supports position detection using AirTAC CMSE reed or DMSE solid-state switches mounted into the dual-side sensor grooves.
This adjustable model utilizes a reduced mounting interface set—Basic, FA, LB, TC, FTC, TCM1, and TCM2—omitting the FB, CA, CB, and CR options. The rear adjuster acts purely as a mechanical stop to set the retraction end position and must not be confused with a locking device, as it cannot hold loads without continuous air pressure.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X475-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 425 to 475 mm retraction point during product size transitions without physically replacing the cylinder or adding external stopper blocks.
Perfect for automated lines where the rear stopper screw must be frequently tuned to accommodate varying package lengths or pusher distances.
Choose this 40 mm bore when an application requires precise variable end-stops during machine setup or product changeover, stepping down from a 50 mm bore (982 N at 0.5 MPa) to save space, or up from a 32 mm bore (402 N) when more thrust is needed. For fixed travel without the need for commissioning adjustments, a standard SAI cylinder is sufficient, but the SAIJ rear screw prevents the need to swap cylinders or add external stops on the line. If your process requires the load to be held mechanically without live air, select the SAIL or BSAI series instead. To replace an ISO 15552 cylinder, match the 40 mm bore, 475 mm stroke, 50 mm adjustment, PT port, and -S magnet.
Because the 475 mm stroke is long, the 16 mm rod and M12x1.25 thread should be guided externally to prevent excessive side-load wear on the seals, even though the rod diameter provides moderate stiffness.
Quick checklist
The rear adjuster screw acts as a mechanical stop that limits the retraction travel, allowing you to shorten the effective stroke by up to 50 mm. This creates a usable travel window of 425 to 475 mm, enabling fine-tuning of the end position during commissioning without changing the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.