
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X60-20 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 60mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X60-20 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster. It provides a usable travel window of 40 to 60 mm, letting you dial back the 60 mm nominal stroke by up to 20 mm during commissioning without adding external stops.
This extruded aluminum barrel omits tie-rods and includes sensor grooves on both sides for CMSE reed or DMSE electronic switches. The M12x1.25 carbon steel rod and PT G1/4 port are bore-specific, while the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2) excludes FB, CA, CB, and CR brackets. The rear screw acts purely as a travel stop, so it will not hold a load without live air pressure.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X60-20 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 40-60 mm travel window during product size changeovers on a packaging line, using the rear stopper to set exact end positions without machining new spacers.
Fine-tune the retract end position during machine commissioning, using the 20 mm adjustment range to compensate for mechanical tolerance stack-up without replacing the cylinder.
The 20 mm adjustment range is ideal for product changeovers on a conveyor, letting operators fine-tune the end position in seconds rather than swapping physical spacers. For load-holding without continuous air, select a SAIL (air-released lock) or BSAI (clamp-lock) cylinder instead, as the SAIJ adjuster is not a brake.
When replacing an ISO 15552 cylinder, match the 40 mm bore, 60 mm nominal stroke, 20 mm adjustment code, PT G1/4 port, and standard carbon steel rod. Since this specific model has a 60 mm stroke, it is short enough that side-loading is minimal, but you should still ensure the M12x1.25 rod thread is aligned to prevent premature seal wear.
Quick checklist
At 0.9 MPa, the push force increases to 1130 N. The operational speed range is 30-800 mm/s.
The rear adjuster screw allows you to shorten the 60 mm nominal stroke by up to 20 mm, creating a usable travel window of 40 to 60 mm. The adjuster acts as a mechanical stop for end-position tuning; it is not a lock and cannot hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.