
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X600-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 600mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X600-100 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that allows you to trim the effective travel back by up to 100 mm. This yields a usable 500-600 mm end-position window, letting you dial in the exact retract distance during commissioning without swapping hardware.
The extruded aluminum barrel includes sensor grooves on both sides, and because this configuration omits the -S magnet, you would add it if you need CMSE reed or DMSE electronic solid-state detection. The standard carbon steel piston rod features an M12x1.25 thread, and the PT tapered porting mates securely with G1/8 fittings. The rear screw acts purely as a mechanical stop for end-position tuning, not as a load lock.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X600-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly reconfigure the retract end-stop by up to 100 mm when switching a packaging line to a different carton size, avoiding the need to physically swap out the entire cylinder.
Fine-tune the 500-600 mm travel window during initial setup to perfectly mate the tooling with the workpiece, compensating for mechanical tolerances without adding external shims.
Act as an adjustable flow diverter on a conveyor, where the exact 40 mm bore push distance (628 N at 0.5 MPa) must be tweaked on the fly to handle varying product widths.
The 100 mm adjustment range is particularly useful on product lines that undergo frequent size changeovers, allowing operators to set new retract stops on the fly instead of installing fixed-stroke SAI cylinders or external jigs. To replace an ISO 15552 cylinder, match the 40 mm bore, 600 mm stroke, PT port thread, and mounting choice from the available SAIJ set: Basic, FA, LB, TC, FTC, TCM1, or TCM2 (this series omits FB, CA, CB, and CR mounts).
Because the nominal stroke is 600 mm, the M12x1.25 rod will experience leverage forces if the load is not fully guided; always use an external linear guide to prevent side-loading damage. Remember that the rear adjuster and air cushions only decelerate the travel end—they do not hold the load without live air. For dead-load holding, select a SAIL pneumatic lock or BSAI clamp-lock cylinder instead.
Quick checklist
If you increase the pressure to 0.7 MPa, the push force rises to 879 N.
The rear adjuster screw lets you shorten the 600 mm nominal stroke by up to 100 mm, creating a usable travel window of 500 to 600 mm. This mechanical stop sets the retract end position but does not lock the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.