
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X600-50S is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 600mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X600-50-S is a double-acting ISO 15552 profile cylinder with a rear stroke adjuster.
This carbon-rod unit includes a magnet for CMSE reed and DMSE electronic sensors, fitting cleanly into the standard extruded aluminum barrel sensor grooves. It uses a G1/4 port and relies on the reduced SAIJ mounting set (Basic, FA, LB, TC, FTC, TCM1, TCM2), omitting FB, CA, CB, and CR mounts.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X600-50S |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 550-600mm retract position when switching product sizes on a packaging line, eliminating the need to physically swap cylinders.
Fine-tune the end-of-stroke stop during initial setup to absorb mechanical tolerances and achieve precise seating without adding external bumpers.
Drive 600mm travel automated assembly tasks where exact final positioning is critical, using the rear screw to set the precise stopping point.
Choose this adjustable-stroke model over a fixed SAI when you need to fine-tune the retract end-position during commissioning or product changeover without adding external stops. If your application requires less force, stepping down to a 32mm bore yields 563N at 0.7 MPa; stepping up to a 50mm bore provides 1374N.
With a 600mm stroke, the 16mm rod needs external guidance to handle side loads and prevent sagging. To match this cylinder for an ISO 15552 replacement, specify: 40mm bore, 600mm stroke, 50mm adjustment, PT tapered port, standard carbon rod, and the -S magnet. Note that the rear adjuster is a travel stop, not a lock; for load-holding without live air, use an external rod lock or explore SAIL or BSAI cylinders.
Quick checklist
A rear adjusting screw acts as a mechanical stopper, allowing you to shorten the effective travel from the 600mm nominal stroke down to 550mm. The adjuster only sets the travel end and does not hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.