
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X800-40 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 800mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X800-40 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that creates a 760 to 800 mm usable travel window. This configuration allows you to dial in the retract end-position precisely during commissioning without swapping out the entire actuator.
Because the nominal stroke is 800 mm, the 16 mm rod and M12x1.25 rod thread will need external guidance to prevent excessive side-loading on the seals. The extruded aluminum barrel includes sensor grooves on both sides, and if you add the -S magnet option, it supports AirTAC CMSE reed and DMSE electronic solid-state switches. Mounting options are limited to Basic, FA, LB, TC, FTC, TCM1, and TCM2, deliberately omitting FB, CA, CB, and CR.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X800-40 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 800 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×800 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the 760 to 800 mm travel window during product size changes without physically replacing the cylinder or adding external shims.
Fine-tune the retract position of a diverter arm on an 800 mm stroke, ensuring precise end-stop alignment while relying on an external guide for the long rod.
Use the 40 mm rear adjustment screw to perfectly tune the end-of-stroke position during initial machine setup, absorbing minor mechanical tolerances.
An adjustable stroke is ideal for product changeovers on a line, letting you shift the end-stop by up to 40 mm rather than machining new hard stops. For any 800 mm stroke, always use an external guide rail to support the load, as the long unsupported rod is susceptible to deflection and side-loading damage.
The rear screw acts purely as a travel stop and works with the variable air cushions at both ends to decelerate the piston; it does not hold the load without live air pressure. For dead-load holding, you must integrate an external rod lock or pilot-operated check valve, or select a related SAIL or BSAI cylinder. To match this ISO 15552 dimensionally interchangeable cylinder exactly, specify the 40 mm bore, 800 mm stroke, 40 mm adjustment, PT tapered port thread, and no magnet.
Quick checklist
If pressure is increased to 0.7 MPa, the push force rises to 879 N.
The rear adjuster screw allows you to trim the effective stroke by up to 40 mm, creating a usable travel window of 760 to 800 mm. It functions as a mechanical stop to set the end position and does not lock the load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.