
The AirTAC SAIJ40 Adjustable Cylinder SAIJ40X950-100 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø40mm bore and 950mm stroke, G1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ40X950-100 is a double-acting ISO 15552 profile cylinder featuring a rear stroke adjuster that permits fine end-position tuning. It provides a usable travel window of 850-950 mm, allowing you to dial back the 950 mm nominal stroke by up to 100 mm during commissioning without adding external stops.
This model features a PT tapered port thread and a 16 mm carbon steel piston rod. The extruded aluminum barrel includes sensor grooves on both sides for flexible mounting of CMSE reed or DMSE electronic switches. SAIJ supports a reduced mounting interface set including Basic, FA, LB, TC, FTC, TCM1, and TCM2, omitting the FB, CA, CB, and CR options found on other variants.
| Model | Airtac SAIJ40 Adjustable Cylinder SAIJ40X950-100 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 950 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 40 | Bore size in mm. |
| ×950 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly dial in the exact retract position within the 850-950 mm window during line changeovers without physically swapping the cylinder or repositioning hard stops.
Adjust the stroke end-position on the fly to accommodate different package lengths on a 40 mm bore actuator handling moderate routing forces.
Fine-tune the final 100 mm of travel on a 950 mm stroke to perfectly seat components, compensating for mechanical tolerance stack-up across a long machine bed.
Choose this adjustable-stroke cylinder when your application requires variable end-stops or frequent product changeovers, rather than relying on a fixed-stroke SAI cylinder. To match this ISO 15552 replacement, specify a 40 mm bore, 950 mm stroke, up to 100 mm adjustment, PT port thread, and no magnet.
Because the 950 mm stroke is quite long, the 16 mm rod will experience greater leverage stresses under side-loading; an external guide bearing is strongly recommended to prevent premature wear. Note that the rear adjuster acts solely as a travel stop and does not hold the load without live air pressure. For true fail-safe load holding, consider the SAIL or BSAI series instead.
Quick checklist
At 0.7 MPa, the push force increases to 879 N. The standard speed range for this bore size is 30-800 mm/s.
A rear adjusting screw acts as a mechanical stop, allowing you to shorten the effective stroke from 950 mm down to as little as 850 mm. This adjuster only sets the travel end and does not lock the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.