
The AirTAC SAIJ80 Adjustable Cylinder SAIJ80BX165-10 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø80mm bore and 165mm stroke, G3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ80X165-10 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster that allows you to trim the effective travel by up to 10 mm. This yields a usable 155-165 mm travel window, enabling precise end-position tuning at commissioning without swapping out the barrel or adding external stops.
This variant is configured with a SUS304 stainless steel rod for superior corrosion resistance and uses PT tapered port threads. The extruded aluminum barrel includes sensor grooves on both sides, ready for AirTAC CMSE reed or DMSE electronic sensors if position feedback is later required. The rear adjuster acts purely as a mechanical stop to set the retract end position; it does not lock or hold the load without continuous air pressure.
| Model | Airtac SAIJ80 Adjustable Cylinder SAIJ80BX165-10 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 165 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 80 | Bore size in mm. |
| ×165 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Dial in the exact 155-165 mm retract position during product size transitions without disassembling the actuator assembly.
Fine-tune the final end position during initial commissioning to perfect the timing of heavy 80 mm bore assemblies.
The 10 mm adjustment range is ideal for machinery where you need slight end-stop variations during product changeovers, avoiding the need to maintain multiple fixed-stroke SAI cylinders for each product size.
When replacing an ISO 15552 cylinder, match the 80 mm bore, 165 mm stroke, 10 mm adjustment range, PT port threads, and standard mounting interface. SAIJ supports a reduced mounting set including Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB, CA, CB, and CR). Because the 165 mm stroke is relatively short, side-load stress is minimal, but always ensure the load is guided externally. For applications requiring the cylinder to hold its position without live air, select the SAIL or BSAI series instead, as the SAIJ adjuster is not a locking mechanism.
Quick checklist
The rear adjuster screw allows you to shorten the nominal 165 mm stroke by up to 10 mm, providing a usable travel window of 155-165 mm. This lets you set the exact retract end position during setup without changing the cylinder.
It operates at speeds between 30 and 800 mm/s.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.